Problem 33-5 Source:
Question 1 - 1st test -
Electric Circuit Course I - School of Engineering - UFRGS - 1976.
In the circuit on the Figure 33-5.1 determine the parameters "h" and find the
values of K and R, knowing that:
a) If I1 = 35A and E2 = 10V so  I2 = 1A
b) If I1 = - 30A  and  E2 = 24V   then  I = 1A.
Figure 33-5.1
Solution of the Problem 33-5
Analyzing the 1st Test
a) If I1 = 35A and
E2 = 10V so  I2 = 1A.
For the first test, the given conditions are shown in the Figure 33-5.2, with
the indication of the currents in the circuit. The resistors that
were in parallel, were replaced by their respective equivalents.
Figure 33-5.2
Making the C mesh, indicated by the green arrow, the following equation is established:
- 4 I - 2 + 10 = 0
Carrying out the calculation, the value of I is found, or:
I = 2 A
And making the mesh A, indicated by the green arrow:
V1 = 32 (2 R) / (2 + R) = (64 R) / (2 + R)
eq. 33-5a
And finally, making the mesh A + B, we find the following equation:
V1 = 2 K + 12 + 8 = 2 K + 20
eq. 33-5b
Considering the two equations for V1 and equating eq. 33-5a to
eq. 33-5b, we find the following relationship:
(64 R) / (2 + R) = 2 K + 20
eq. 33-5c
Analyzing the 2nd Test
b) If I1 = - 30A and
E2 = 24V so  I = 1A.
The circuit shown in the Figure 33-5.3, expresses
the conditions of the second test, including the flow and values of the currents in the circuit.
Figure 33-5.3
The value of I2 is found by doing the mesh equation C. Note
that, according to test data, the value of I is 1A. Thus, in the resistance of
2 ohms flows a current of 2A, and this causes a potential difference of
4 volts on it. This way:
- 4 - 2 I2 + 24 = 0 or I2 = 10 A
Making the mesh A, indicated by the green arrow, the following relationship is established:
V1 =-22 (2 R)/(2 + R) = -(44 R) / (2 + R)
eq. 33-5d
Using the same reasoning for the B mesh, indicated by the green arrow, we obtain the following
relationship:
V1 = K - 32 + 4 = K - 28
eq. 33-5e
Repeating the process done previously, and equating eq. 33-5d to
eq. 33-5e, you get:
- (44 R) / (2 + R) = K - 28
eq. 33-5f
Repeating the equation eq. 33-5c, found earlier,
a system of two equations with two unknowns is achieved, when used in conjunction with eq. 33-5f.
(64 R) / (2 + R) = 2 K + 20
eq. 33-5c
Solving the system we easily find the values of K and R. Soon:
R = 2
K = 6
With the values of K and R determined, from this moment on, you can
calculate the parameters "h" of the circuit. These parameters have the following equations:
V1 = h11 I1 + h12 V2
I2 = h21 I1 + h22 V2
h11 and h21 are calculated by doing
E2 = 0. Therefore, if E2 = 0, that is,
short circuit at the output, the resistance of
2 ohms where I2 circulates, it is in parallel with the other
resistor of 2 ohms, through which a current of 2 I flows.
It follows that I2 = - 2 I, as they are under the same
potential difference. Based on this conclusion, the current arriving at point c
is 4 I. See the Figure 33-5.4 for the information indicated in the circuit.
Figure 33-5.4
Setting V1 = 26 volts, calculate the current I, as:
- 26 + 6 I + 16 I + 4 I = 0
So the value of I is:
I = 1 A
From this data, it is concluded that:
I1 = 30 A
I2 = - 2 A
At this moment, one can calculate h11 and
h21. Then:
h11 = V1 / I1 = 26 / 30 = 13 / 15 Ω
h21 = I2 / I1 = - 2 / 30 = - 1 / 15
To determine the parameters h12 and h22,
you must make the current I1 = 0. See the Figure 33-5.5.
Figure 33-5.5
A current source of 12A is placed at the output. Like this,
I2 = 12A. Making the mesh in the direction indicated by the green arrow,
the following relationship is established:
-I2 + 2 I + 6 I - 4 I2 + 8 I + 4 I = 0
Remembering that I2 = 12A and performing the calculation determines the value
from I. Soon:
I = 3 A
Now you can calculate the values of V1
and V2.
V1 = 1 (I2 - 2 I) = 6 V
In turn, V2 holds:
V2 = 2 I2 + 4 I = 36 V
All data needed to calculate h11 and
h21 were calculated. Then:
h12 = V1 / V2 = 6 / 36 = 1 / 6
h22 = I2 / V2 = 12 / 36 = 1 / 3 siemens
Therefore, the quadripole equations are as follows: