Problema 15-21 Source:
Problem 2 of P1 - 1st semester - 2016 -
Subject: Electrical Circuit Engineering Analysis - ULBRA -
Prof. Dr. João Carlos Vernetti dos Santos.
In the circuit shown in Figure 15-21.1, when switch S is in position 1
the current I = 1.2 A. Determine the value of the voltage Vab when the
key S is in position 2. The voltage V1 follows the graph shown
in Figure 15-21.2.
Figure 15-21.1Figure 15-21.2
Solution of the Problem 15-21 -
Thévenin Method
When the key "S" is in position 1, the points a and b are
interconnected by a resistor with a value equal to 1 Ω and through which a
electric current of 1.2 A. This information makes it possible to calculate the
Thévenin equivalent for the circuit highlighted by the dashed line in blue.
To do so, independent sources are eliminated and the Thévenin resistance is calculated.
Note that when we eliminate the voltage sources E1 and E2
(they are short-circuited),
the three 12 Ω resistors are in parallel with each other. Thus, we obtain a single
equivalent resistor with a value equal to 4 Ω. On the other hand, when we eliminate sources of
current I1 and I2,
they behave like an open circuit and, therefore, we can eliminate them from the circuit.
Figure 15-21.3
In Figure 15-21.3, we can see the simplified circuit that
will allow you to calculate the Thévenin resistance. Thus, the two 4 Ω resistors
which are in series, can be replaced by a single resistor with a value equal to 8 Ω.
This in turn will be in parallel with the 24 Ω resistor. As a result of
parallel, we obtain an equivalent resistor of 6 Ω. And finally, adding the value of this resistor with the
2 Ω, which is connected to point a, we find the value of Rth1. Let's call it that,
because we must calculate Rth2, referring to the circuit
highlighted by dashed lines in green. Logo:
Rth1 = 8 Ω
Having the value of Rth1 and considering the key S in
position 1, we can now calculate the value of Vth1. For that,
follow the circuit shown in Figure 15-21.4.
Figure 15-21.4
We know that when we insert the 1 ohm resistor into the Thévenin equivalent, a
current of 1.2 A through the circuit. Therefore, applying Ohm's law to the circuit,
we easily calculate the value of Vth1. The result is:
Vth1 = 9 x 1.2 = 10.8 volts
Let's pay attention to the other circuit (to the right of points a-b), and calculate its
Thévenin equivalent.
Initially let's reveal what the corresponding graph means
to circuit A. From the graph shown in Figure 15-21.2, we realize that when i = 0 the voltage
V1 is equal to 15 volts. However, we know that when i = 0, this
represents an open circuit. On the other hand, when V1 = 0
(i.e. a short circuit) then the electric current assumes the value of 3 A.
Figure 15-21.5
Note the circuit shown in Figure 15-21.5. When the circuit behaves
as an open circuit, we have i = 0 and therefore V1 = 15 V.
However, if we apply a short circuit to its output (V1 = 0 V),
for a current i = 3 A to circulate, we must have a resistor in
series with the voltage source equal to R = 15/3 = 5 Ω.
Thus, the circuit presented above satisfies the conditions required by the graph.
This way, we can redraw the circuit highlighted in a dashed line in green.
We can also replace the "box" that represents circuit A, shown in dashed red.
Then, based on this information, we obtain the circuit shown in Figure 15-21.6.
Figure 15-21.6
Note that, in addition to introducing the circuit
from "box A", we made a explosion of the voltage source of 7.2 volts
(right side of the circuit).
Now, it is easy to see that we can transform the entire circuit that is highlighted
by the green dashed line into a single voltage source in series with a resistor. Follow Figure 15-21.7
the transformations carried out in the circuit.
Figure 15-21.7
Note that the circuit shown on the right, in the figure above, is exactly the
Thévenin equivalent of the circuit we are analyzing. Note that Rth2 = 4 Ω and
Vth2 = 12.27 V. We could have
another method is used to find the result. However, note that doing
source transformations we quickly get to the final result.
As we have the two Thévenin equivalents the only thing left to do is connect them
and calculate the value of Vab. See Figure 15-21.8 how it turned out
the final circuit.
Figure 15-21.8
Note how the circuit in the figure above made it easy to determine the value of
Vab, as it is enough to apply Ohm's law to the circuit.
Note that this case is when the key S is in position 2.
Therefore, we can calculate the current I.
I = (12.27 - 10.8) / ( 8 + 4) = 0.1225 A
Using the value of the current flowing through the circuit, we can calculate the voltage
Vab, or:
Vab = 10.8 + 8 x 0.1225 = 11.78 volts
For this calculation we use the circuit to the left of points a - b.
We would arrive at the same result using the circuit to the right of points a - b. Check!!