Problema 14-9 Source:
Problem developed by the website author.
In the circuit shown in Figure 14-09.1, calculate:
a) the currents ix and iy;
b) the power dissipated in the 6 Ω resistors.
Figure 14-09.1
Solution to the problem using the Source Transfer Methodclick here!
Solution of the Problem 14-9 -
Superposição
Item a
This is a problem that, to be solved using the superposition method, requires building three circuits,
eliminating one source at a time. It's left as a task for anyone who wants to attempt a more extensive solution.
Therefore, it was decided to present the solution using the Basic Circuit Method,
a method seen on the theory page. To refresh your memory, access:
Basic Circuit Method
To do this, three source transformations must be performed simultaneously, as shown in
Figure 14-09.2 in the regions highlighted in green and yellow.
Figure 14-09.2
In the circuit highlighted in yellow, it can be seen that the voltage source of 36 volts
can be transformed into
a current source of 12 A. And the resistor of 3 Ω will be
in parallel with the resistor of 6 Ω. Solving this parallel circuit, we find
an equivalent resistor of 2 Ω.
On the other hand, in the circuit highlighted in green, the two current sources have been transformed
into two voltage sources.
Note that the two voltage sources will have opposite polarities. Therefore,
their values must be subtracted, and the positive pole must face the side
of the source with the higher voltage (in modulus). And the two resistors of 5 Ω
will be in series, totaling a single resistor of 10 Ω. You can
see all these transformations in Figure 14-09.3.
Figure 14-09.3
This gives us the circuit with the desired configuration.
Analyzing the circuit, we can write the equation that determines the voltage at node a, or:
Va = 2 (12 - ix)
Transforming the current source of 12 A, which is
in parallel with the resistor of 2 Ω, we obtain a voltage source
of 24 volts and, by connecting the two resistors in series, we obtain
a single equivalent resistor of 10 Ω. This is on the left side of the circuit. On the right side, simply
subtract the values of the voltage sources, resulting in a single voltage source of 20 volts
with the positive polarity facing up, as shown in Figure 14-09.4.
Figure 14-09.4
Based on the basic configuration studied in the Basic Circuit Method section in the “Basic Theory”,
we can identify the resistors as:
R1 = 10 Ω, R2 = 6 Ω
and R3 = 10 Ω
Thus, once the resistors have been identified, it is possible to calculate the denominator
of the equation represented by Rsp, which is given by:
Rsp = R1 R2 + R1 R3 + R2 R3
Replacing the variables with the respective numerical values of the resistors that make up the circuit and performing the calculation,
we find:
Rsp = 10 x 6 + 10 x 10 + 6 x 10 = 220
Now we just need to find the numerator by cross-multiplying the voltage sources of 24 and 20 volts,
representing V1 and
V2, respectively, by the resistors
R3 and R1, or:
V1 R3 + V2 R1 = 24 x 10 + 20 x 10 = 440
And finally, dividing this value by Rsp, we find the value of
iy.
iy = 440 / 220 = 2 A
Knowing the value of iy, to find eb simply multiply by the value of
R2 (Ohm's law), resulting in:
eb = R2
Vb = R2 iy = 2 x 6 = 12 volts
Knowing the value of Vb, it is easy to calculate the value of ix,
because:
ix = (24 - Vb)/ R1 = (24 - 12)/ 10 = 1.2 A
With this value calculated, we can calculate the stress at node a. The equation has already been
determined, and we will repeat it here.
Va = 2 (12 - ix)
Substituting the variables with their respective numerical values and performing the calculation,
we find:
Va = 2 (12 - 1.2) = 21.6 volts
From here on, all you have to do is add and subtract, obeying the
law of nodes and Ohm's law.
Thus, Figure 14-09.5 shows the complete circuit with all indications
of the values of the currents flowing through the circuit components.
Figure 14-09.5
Item b
To complete the solution to the problem, the power dissipated in the
resistor of 6 Ω connected to node b must be calculated:
Pb6 = 6 iy2 = 6 x 22 = 24 watts
To calculate the power dissipated in the resistor of 6 Ω that is
connected to node a, the voltage Va = 21.6 volts is used, or: