Problem 12-13 Source:
Problem 70 from the Electrical Circuits I list,
from the School of Engineering, UFRGS, Prof. Dr. Valner Brusamarello.
In the circuit shown in Figure 12-13.1, it is known that when switch S is in position 1, the ammeter
A registers a current of 5 A. If switch S is in position 2, then
ammeter A registers a current of 14 A.
Find the values of I and K.
Figura 12-13.1
Solution of the Problema 12-13
First, let's analyze the circuit when switch S is in position 1. To do this,
let's redraw the circuit to better understand how it works. Never forget that an ideal ammeter
has an internal resistance equal to ZERO, so it acts as a short circuit and there is no voltage drop
across it. See Figure 12-13.2 for the circuit redrawn in position 1 .
Figure 12-13.2
At position 1, the ammeter reads 5 A. So, this current passing
through the 12 Ω resistor generates a voltage at point a of
Va = 60 volts. Knowing the voltage at point a,
we can calculate the currents in all the resistors in the circuit. See in the figure
above, in blue, the values of the currents found by dividing the value of
60 volts by the value of each resistor. Note that a current of 5 A flows through the 4 Ω resistor
and, as a result,
we find V = 20 volts. Now, using Kirchhoff's law
for node a, we find:
I + 20 K = 20 + 5 + 20 + 5 = 50 A
That is, the two current sources together must supply a total of 50 A. From the first
piece of information provided by the problem, we obtain the above equation. To use the second piece of information, we must
redraw the circuit as shown in Figure 12-13.3.
Figure 12-13.3
Let's take a closer look at the part of the circuit highlighted in yellow. Note that we have two
current sources. Let's explode the current sources. See
in Figure 12-13.4 how the part of the circuit highlighted in yellow looks now.
Figure 12-13.4
Note that we can connect the current sources in parallel. In Figure 12-13.5,
we can see the final circuit with the currents indicated in blue.
Looking at the circuit highlighted in yellow, using Kirchhoff's law for node b, the current passing
through the resistor highlighted in green is equal to zero.
Therefore, we can disregard the circuit highlighted in Therefore, we can disregard the circuit highlighted in green.
Thus, point b is at the same level as the ground potential green.
Figure 12-13.5
After these considerations, we can redesign the circuit as shown in Figure 12-13.6.
The 2 Ω resistor, through which current i flows (by definition
in the problem statement), and which is
in parallel with the current source i, causes this current
to be confined to these two components. Thus, the current of 14 A that leaves
the circuit at point c passes through the other resistor of 2 Ω,
causing a voltage drop of 2 x 14 = 28 volts.
Note that this voltage is the same as that across the 2 Ω resistor through which the
current i flows. Therefore, we can write:
2 i = 28 ⇒i = 14 A
Figure 12-13.6
Thus, with the determination of the value of the current i, we realize that through the resistor
of 1 Ω, which is in parallel with the current source i, at the top of the circuit,
no current passes, since the 14 A that enter
pin 2 will pass through the current source i, with nothing passing
through the 1 ohm resistor. This indicates that the voltage drop across the
current source i, which appears at the top right of the circuit, is V1c = ZERO.
Therefore, we can remove the
1 Ω resistor from the circuit, as well as the 2 Ω resistor and the current source
i (which are in parallel), as they do not affect the operation of the circuit.
The circuit is then reduced to what appears in Figure 12-13.7.
Figure 12-13.7
Adding up all the currents indicated in the circuit by the blue arrows that reach
node b, we find the value
of 14 + 14 + 14 + 3.5 = 45.5 A. In addition, the voltage V across the
4 Ω resistor is 4 x 3.5 = 14 volts. Thus, the current source K V has a
value of 14 K. Looking at the circuit, we can see that the two current sources, I and
KV, are responsible for supplying the 45.5 A. Remembering that V = 14,
we can write the other equation we need to solve the problem, or:
I + 14 K = 45.5
Repeating the first equation here, we have a system of two equations with two unknowns.
I + 20 K = 50
Solving this system gives us the values of the variables requested in the problem, that is:
K = 9 / 12 = 3/4
I = 35 A
Power Balance
Let's take balance of Power.
See Figure 12-13.8 for how the circuit looks with the currents in the branches indicated.
Figure 12-13.8
Let us first calculate the power dissipated in the resistors, remembering that,
by convention, we consider these powers to be POSITIVE.
Now, to calculate the power in the sources, let's remember
that voltage sources with current flowing out of the positive terminal are considered
NEGATIVE powers, since they are supplying power to the circuit. Otherwise,
they will be POSITIVE powers. The same applies to current sources.
PF35 = - 35 x 42 = - 1,470 watts
PF10.5 = - 10.5 x 42 = - 441 watts
The power supplied to the circuit comes exclusively from the current sources.
∑ P- = - 1,470 - 441 = - 1,911 watts
Finally, we know that the algebraic sum of the powers supplied and received in a circuit must be equal to ZERO, that is:
PTotal = ∑ P+ + ∑ P- = + 1,911 - 1,911 = 0 watt
Note that we do not take into account the power of the current source
i = 14 A, since the potential difference across it is zero. Therefore,
the power supplied or absorbed is also zero. For the current source i
in parallel with the 2 ohm resistor, we also do not calculate it, since the resistor
absorbs all the power from the source.
Therefore, the circuit satisfies the node law and the mesh law, as well as
the power balance.